Replacing broken screen on Herald p4350 (tmobile wing)

[jdep1]

-How to replace the screen on a T-Mobile Wing
HTC Herald, HTC P4350
**I (ME) or Wckediden, not responsible for any damage cause to your device. Use the guide at your own RISK**
Tools that you need:
•Replacement screen
•Small Torx screwdriver (T6)
•Small Phillips screwdriver
•Small flat screwdriver

Take the phone Apart:
Remove the stylus.
Remove the back cover.
Remove the battery.
Slide the SIM card latch down and remove the SIM card.
Remove the Micro SD card from the slot on the side
Use the Torx screwdriver to remove the four screws that hold the two case-halves together.
Lift the upper part of the case back off and set it aside.
Remove the rest of the case back. It is snapped together so you'll probably need to pry it apart with your fingernail or a small flat screwdriver. You shouldn't have to pry too hard; don't crack the case.
Use a small Phillips screwdriver to remove the screw that holds the PCB in place.
Disconnect the ribbon cable that goes to the keyboard. Do this by first removing the piece of clear yellow tape (if present) that is covering the connector. Next flip up the brown plastic latch (it lifts up on the ribbon side of the connector). The ribbon cable should now easily slide out of the connector.
Gently pry the PCB away from the top half of the case. You should be able to see the ribbon cable that goes to the screen and front panel buttons. Remove the piece of tape (if present) and disconnect the connector by gently prying it away from the PCB. Set the PCB aside.
Use the Phillips screwdriver to remove the 6 screws that hold the screen assembly onto the rest of the phone.
Use the Torx driver to remove the four screws that hold the screen assembly together.
The two halves of the screen assembly are snapped together like the two main case halves were. Use your fingernail or a flat screwdriver to gently pry the halves apart.
Remove the two Phillips screws that hold the front panel button PCB in place
Gently pry the screen and button PCB away from the case. You should now have access to the ribbon connector for the screen.
Disconnect the ribbon cable by flipping the connector's latch up and sliding the cable out. The old screen is now free from the phone.

INSTALLING THE NEW SCREEN:
Connect the ribbon cable for the new screen. If you are using an aftermarket screen the ribbon might look different or come out of a different part of the screen. That's okay as long as the end fits into the connector.
Flip everything back over. Set the button PCB and the new screen into place. Everything should fit together properly. The screen may get pushed up a little bit if you had to make a new bend in the ribbon, but it will be held in place when you put the screen assembly back together.
This is the time to remove the protective plastic from the front of the screen. If you don't do it now you won't be able to get to the edges to peel it off
PUTTING THE WING BACK TOGETHER:
Reassembly is basically the reverse of disassembly. It should be pretty straightforward, but here are a couple of hints:

•Make sure you get the ribbon cable inserted into the connector all the way (it's a bit tight).
•Before you snap the two case halves back together, make sure the volume up/down slide switch cap lines up with the actual switch on the PCB.

When you are all done, turn the phone on and test the display, backlight and touch screen. You'll probably want to calibrate the new touch screen (Start > Settings > System > Screen > Align Screen).
that is not my video i found it on youtube but it should help

Code

Code

http://www.youtube.com/watch?v=JjJmghB7-iQ

[jr5416]

Great gob bro someone here will find this very useful,

[GokuSS3]

Why did you post this as a Release ?

[jr5416]

“ Originally Posted by GokuSS3 ”

Why did you post this as a Release ?

Looks like its on the right section bro it say tutorial maybe someone moved it already .

[jdep1]

i did post on the tutorial section. You might of read it wron but anyway i hope this helps other users that also have the tmobile wing. i just thought we needed more articles like this one

[D/\SH]

“ Originally Posted by jdep1 ”

i did post on the tutorial section. You might of read it wron but anyway i hope this helps other users that also have the tmobile wing. i just thought we needed more articles like this one

you placed it in the tutorial section which is correct and thank you for the tutorial!!! and yes any bit of info to place on the boards is great